Sandpiper Liquid Level Control 032.036.000 Instrukcja Użytkownika Pobierz pdf

w w w .s a n d p i p e r p u m p .c o m

Warren Rupp, Inc.

A Unit of IDEX Corporation

800 N. Main St.,













SERVICE & OPERATING MANUAL

Original Instructions

ACCESSORIES

Features & Benefits:

• Completely automatic operation.

• Easy, low-cost installation. The control is plumbed as

part of the piping system.

•All pneumatic operation - no electrical connections.

• Versatility. One control can be installed to handle

sumping and tank filling/transfer.

•For sumping operations, the pump is started at a high

liquid level, and stopped at a low liquid level. For tank

filling and transfer, the pump is started at a low liquid

level and stopped at a high liquid level. It’s completely

adjustable to any liquid level operating range. It will

adjust from a few inches to approximately nine feet.

• Long life operation. Corrosion-resistant wetted parts.

• High capacity air valve. Accomodates air flow

requirements up to 125 cfm, with a pressure drop less

than 10 psi.

How It Works:

This liquid level control operates entirely by mechanical

and pneumatic means. A float-operated air pilot valve

controls the opening and closing of an air valve. It admits

or exhausts air through a special regulator to turn an air-

operated pump on or off.

Installation:

The line air valve and air pilot valve are

preassembled on bracket and ready for mounting to

1½1/2” (3.81cm) standard on pipe.

Unit is ready as recieved for standard (high level on

- low level off) operation. For reverse operation (low level

on - high level off), remove bracket (item 1) from pilot valve

by removing hex nut (item 12). Install bracket opposite

direction from position shown and action is reversed.

Install float and rod as shown and mount rod guide

bracket below control as required. A minimum of 10 PSI

(.6895 BAR) air pressure is recommended for operation

of liquid level control.

Air In and Air Out are noted on the regulator.

Note:

Important - a minimum of 8 PSI, created through pump

application, must exist for the float valve to work.

Liquid Level Control

032.036.000

SANDPIPER’s float

actuated air valve and

liquid level control provides

all pneumatic operation.

Especially useful in

sumping and liquid transfer

situations, the float actuated

switch opens and closes

air supply to the pump for

positive ON-OFF response.

1 2 3 4

Podsumowanie treści

Strona 1 - Liquid Level Control

w w w .s a n d p i p e r p u m p .c o mWarren Rupp, Inc.A Unit of IDEX Corporation800 N. Main St.,  

Strona 2

www.sa n dpipe r pump .comspllcsm-rev0513Liquid Level Control16517182414 15631792QTAIR INLET1219138137161717173181792112193TO

Strona 3 - Float Actuated Air Valve

www.sa n dpipe r pump .comspllcsm-rev0513Float Actuated Air ValveGrounding the Liquid Level Control16517182414 15631792QTAIR I

Strona 4 - EC Declaration of Conformity

In accordance with ATEX Directive 94/9/EC, ANNEX VIII, Equipment intended for use in potentially explosive environments.Applicable Standards:EN 13463-

Komentarze do niniejszej Instrukcji

Brak uwag

Sandpiper Liquid Level Control 032.036.000 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Sandpiper Liquid Level Control 032.036.000. SANDPIPER Liquid Level Control 032.036.000 User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Sandpiper Liquid Level Control 032.036.000